San Antonio homeowners
Sprinkler head repair: not popping up, leaking, clogged, or spraying the wrong way
Most head problems are a quick fix: clean the riser, swap the nozzle or reset the arc. If several heads on a zone are weak, it's pressure, not the head.
Fix your sprinklersOn this page
Most sprinkler head problems are a simple fix
Heads are the part of the system you can see, and the part that gets hit by mowers, edgers, tires and feet. Most head problems are a simple fix with a part from the hardware store. This guide covers the common ones for Rain Bird and Hunter pop-up heads. It also covers the head problems that are really pressure problems, which no new head will fix.
If you would rather have it done, call 210-697-9086.
Which sprinkler head you have (Rain Bird, Hunter, Orbit)
Most San Antonio lawns run pop-up spray heads (Rain Bird 1800 series or Hunter Pro-Spray are the common ones) on small areas, and rotors (Rain Bird 5000, Hunter PGP) on larger ones. A spray head has a riser that pops up and a nozzle on top with a fixed arc. A rotor turns a single stream. The brand and model are printed on the cap. Match replacements to the same brand and nozzle size, or the zone's precipitation rate (how fast the heads put water down, in inches per hour) goes off and you get dry and wet patches. The arc is the slice of circle a head covers. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Sprinkler head not popping up
In order of likelihood: low pressure on that zone (a leak or a valve problem, not the head). Dirt in the riser seal. So the head sticks down. A riser seal worn out. A head buried by grass growing over it. Clean the riser (the part that pops up. Pull it up by hand and rinse the rubber seal around it), trim the grass, and if it still sticks, replace the head. If several heads on the zone are sluggish, it is pressure. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Sprinkler head leaking at base
Water pooling around a head when the zone runs usually means the riser seal has failed or the head is cracked at the body. Replace the head. Water seeping from a head when the system is off is low-head drainage: the zone draining through its lowest head after each run. The fix is a check-valve head (a head with a built-in valve that holds water in the pipe: Rain Bird SAM or Hunter check valve) at the low points, which SAWS also lists as a check on new-system inspections. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Clogged sprinkler head, or how to replace a sprinkler nozzle
Unscrew the nozzle (the small cap the water comes out of), rinse it and the small filter screen under it, screw it back on. If the spray pattern is still broken, replace the nozzle with the same size. A head that sprays a thin fan or mists is usually running at too high a pressure, not clogged. A pressure-regulating spray body (a head with a built-in regulator) stops the misting. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Low pressure sprinkler heads
One or two weak heads at the end of a long run are usually clogged. Several weak heads on one zone, or weak heads on every zone, are a pressure or leak problem and no new head will fix them. See our leak and low pressure guide. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
How to adjust a Rain Bird pop-up head
Rain Bird 1800 spray heads: with standard nozzles, the arc is fixed by the nozzle (a quarter, half, or full circle). To change the arc you change the nozzle, or use a VAN (variable arc) nozzle and turn its collar. To adjust the radius (how far it throws), turn the small screw on top of the nozzle clockwise to reduce it. To aim the head, pull the riser up and twist it. For Hunter heads and rotor arc settings, see how to adjust sprinkler heads.
Rain Bird 5000 rotors: the left edge of the arc is the fixed stop.
Pull the turret up and turn it counterclockwise to the left stop. If it does not turn easily to the left, first turn it clockwise to the right stop (Rain Bird's caution).
Put a flat screwdriver or the Rain Bird rotor tool in the arc socket on top.
Turn clockwise to widen the arc, about 90 degrees per full turn, or counterclockwise to narrow it.
Hunter PGP rotors are the mirror image: the fixed stop is the right edge. Turn the turret clockwise to the right stop, hold it there, put the plastic key end of the Hunter wrench in the socket and turn clockwise to widen (a full turn adds about 90 degrees).
Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
How to replace a Hunter sprinkler head
Dig a few inches around the head.
Unscrew the whole body from the fitting below, counterclockwise.
Screw on the new body with the riser at the old height.
Flush the line for a few seconds with the nozzle off.
Fit a nozzle the same size as the old one.
Check the manufacturer's instructions before mixing bodies and nozzles; parts that fit are not always matched in flow. Digging near buried pipe and wire can cut them, so dig carefully by hand, and remember Texas law requires a call to 811 at least two business days before digging, even in your own yard. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Rotor won't rotate or is stuck in one position
A gear-driven rotor (Rain Bird 5000, Hunter PGP) that sprays but will not turn has grit in the gear drive or the turbine (the small water wheel that drives it), or too little pressure to drive it. Pull the riser up, rinse the top, and run the zone. If it still will not rotate, the internal riser assembly is worn and is swapped for a new one without digging up the body. A rotor that turns past its stops needs its arc reset with the adjustment tool, as in the steps above. On an impact head (the old clicking type, such as the Rain Bird Maxi-Paw), the trip arm is bent or the bearing is seized, and replacement is the usual answer. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Orbit and other store-brand heads
Heads from other brands, including store brands such as Orbit, follow their own manufacturer's instructions. Nozzles from different brands can thread on but differ in arc, flow rate and fit, so a mixed zone can water unevenly. Replace like with like using the part number printed on the head or its manufacturer's guide, or ask a licensed irrigator about re-heading the zone to one brand. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Spraying the street, the house, or the fence
Overspray wastes water, counts as water waste under SAWS rules, and fails a SAWS inspection on new systems. Fix it by aiming the head, changing to a nozzle with the right arc, or reducing the radius with the screw. On new systems SAWS wants heads at least 4 inches from pavement. So a head closer than that needs moving, not adjusting. See the SAWS watering rules. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Water keeps seeping from the lowest head after the zone shuts off
If one head, always the lowest one on the zone, dribbles for a few minutes after every run and then stops, the cause is usually low head drainage. The water left in the pipe drains downhill and out through the lowest head. Nothing is broken, but it wastes water, leaves a soggy spot and can stain a sidewalk.
The fix is a head with a built-in check valve, or a check valve added under the head, which holds the water in the pipe when the zone is off.
How to tell it from a leaking valve: low head drainage stops within a few minutes. A valve that is not closing fully keeps the head wet all day, and the seeping does not stop. That one is covered in our valve guide.
Elsewhere in Texas
Heads that spray the street can bring a fine in many Texas cities. Dallas bans spraying driveways, sidewalks and streets, and requires broken heads to be fixed. Fort Worth bans runoff from broken or misaimed heads. El Paso bans water flowing into the street. On new systems, Texas rules keep heads at least 4 inches from pavement. In Greater San Antonio, reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Sprinkler head questions
Why is my sprinkler head not popping up?
Most often low pressure on that zone (a leak or valve issue), or dirt in the riser seal. Pull the riser up, rinse it and the seal, and clear any grass over the cap. If several heads on the zone are weak, fix the pressure first.
How do I adjust a Rain Bird pop-up sprinkler head?
On 1800 series spray heads, the radius screw on top of the nozzle reduces the throw. The arc is set by the nozzle or by turning a VAN nozzle's collar. Aim by twisting the riser. Rain Bird 5000 rotors adjust with a flat screwdriver or the Rain Bird rotor tool in the arc socket on top.
Why is my sprinkler head leaking at the base?
A failed riser seal or a cracked body when the zone is running. Replace the head. If it seeps when the system is off, the zone is draining through its lowest head and a check-valve head stops it.
Can I mix Rain Bird and Hunter heads on the same zone?
You can, as long as the precipitation rates match. A zone with mixed spray and rotor heads, or mismatched nozzle sizes, waters unevenly. SAWS requires precipitation rates within 15% on any new-system plan it reviews. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Related pages
Start here: All sprinkler guides.
Also useful: Sprinkler zone not working. Sprinkler controller not working. Leaks and low pressure.
Need help? Sprinkler repair in San Antonio.
When to call SISCO
A zone where several heads are weak, repeated head breaks on the same run, overspray you cannot aim out, or a system that has grown unevenly over the years: call 210-697-9086 or request sprinkler repair. We reset the zone's coverage, not just the one head. We carry Rain Bird parts on the truck.
Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
