San Antonio homeowners
Sprinkler zone not working? Check these in order
A dead, weak or stuck zone comes down to four places: the controller, the wire, the valve or the water supply. Start with the symptom.
Fix your sprinklersOn this page
Four places a sprinkler zone can fail
A zone is a group of heads run by one valve (in the green box in the lawn), switched by the controller through a wire to the valve's solenoid (the black cylinder on top of the valve). When a zone misbehaves, the fault is in one of four places: the controller, the wire, the valve, or the water supply to it.
Which one depends on the symptom, so start with the symptom. The same checks apply to a Rain Bird, Hunter or Orbit system. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
None of my sprinkler zones are working
If no zone runs from the controller, the fault is upstream of the valves. Check these in order:
Check that the controller has power and isn’t set to “off” or rain delay.
Check that the rain sensor isn’t holding the system off; flip its bypass switch.
Check that the isolation valve at the backflow preventer is open.
Check that the common wire, usually white, is connected at the controller (on a plug-in controller, unplugged first; on a hardwired one, call a licensed electrician).
Turn one valve’s solenoid a quarter turn counterclockwise: if the zone runs by hand, the fault is electrical; if not, the water is off. Turn it back clockwise afterward.
Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
One sprinkler zone not working
Run it from the controller and go to its valve. A click or hum at the solenoid means the controller and wiring are fine and the valve is stuck; no click means the wire or the solenoid. To test the wiring: unplug the controller (only open a plug-in controller; if yours is wired straight into house power, do not open it, and have a licensed electrician do any work inside), swap the zone's wire with a working zone's at the terminals (the numbered screw connections inside the cabinet), restore power and run the zone. The zone wires themselves are 24-volt low voltage. If the dead zone now runs, the controller terminal is bad. If it is still dead, the wire or solenoid is. Valve details are in our sprinkler valve guide. Stuck here? Call 210-697-9086.
How many heads per zone?
A zone can feed only as many heads as the supply flow allows. Add up each nozzle's flow in gallons per minute (from the manufacturer's nozzle chart) and compare the total with the flow you can actually get, which depends on your pressure, meter, service line and pipe size. Head counts that work on one property fail on another, so there is no safe rule of thumb. Adding a head to a zone that already runs weak makes every head weaker. Sizing a zone is a job for a licensed irrigator, so call us at 210-697-9086 before you add heads.
Why does one sprinkler zone have low water pressure?
A lateral line break on that zone, a flow control turned down at the valve, a fouled diaphragm, or more heads on the zone than the supply can feed (common after heads were added over the years). If the zone used to be fine and now is weak, suspect a break first and walk the zone looking for a wet spot. See our leak and low pressure guide. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
A zone runs together with another zone
Two zones running at once means two valves open: a controller wired with two zone wires on one terminal, or a valve stuck open from debris while another runs. Check the terminals first. A loud bang when zones change over can be water hammer. See our sprinkler valve guide. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
One zone won't turn off
The valve for that zone is stuck open: debris or a torn diaphragm, or a solenoid left in the manual-open position after someone turned it. Close the isolation valve to stop the water, then clean or replace the diaphragm. If the zone only runs at the wrong time rather than nonstop, it is the controller program, not the valve. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
How long should each zone run?
Long enough to put down about an inch a week in summer, split across your SAWS watering windows, and in two cycles if water runs off. The run times by head type, the current SAWS windows and controller setup steps are on our SAWS watering rules page. A zone that needs far longer than the norm to stay green has a coverage or pressure problem, not a schedule problem. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
How to add a zone to a sprinkler system (or split one)
A zone that was always weak, or a new bed, often needs its own valve. Digging for a new valve or wire needs an 811 call at least two business days ahead, even in your own yard. Adding a zone means a new valve in the manifold (the group of valves in the box), a new wire to the controller (or a spare in the existing cable), and a controller with a free station (a numbered zone terminal). Splitting an overloaded zone is the same job. Check first that the controller has a free station, and keep spray heads and drip on separate zones. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Elsewhere in Texas
A stuck rain sensor is a common reason no zone runs. Texas requires a rain sensor on new automatic systems in most of the state. Dallas requires one on every automatic system. Fort Worth requires one on systems put in since June 1, 2007. Watering days differ by city. Austin homes water once a week. Dallas and Fort Worth water twice. El Paso waters up to three days. In Greater San Antonio, reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Sprinkler zone questions
Why are none of my sprinkler zones working?
The fault is before the valves: controller power or mode, a rain sensor holding the system off, a closed isolation valve, or a disconnected common wire. Run one zone by hand at its valve to tell whether the problem is water or electrical.
Why does one sprinkler zone have low water pressure?
One weak zone usually has a break on its lateral line, a valve flow control turned down, a fouled diaphragm, or too many heads on the zone. Walk the zone while it runs and look for a wet or sunken spot first.
How long should sprinklers run in each zone?
About an inch of water a week in summer, split across your watering windows. The run times by head type are on the SAWS page. A zone that needs much more than that has a coverage or pressure problem.
Why won't one of my sprinkler zones turn off?
Its valve is stuck open, almost always debris under the diaphragm or a torn diaphragm. Close the isolation valve, then clean or replace the diaphragm. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Related pages
Start here: All sprinkler guides.
Also useful: Sprinkler controller not working. Smart controllers and drip. Sprinkler head problems.
Need help? Sprinkler repair in San Antonio.
When to call SISCO
A zone you cannot bring back with the checks above, wiring you cannot trace, a controller terminal that is dead, or a zone that needs splitting: call 210-697-9086 or request sprinkler repair. We find the fault zone by zone and leave the system on your water provider's schedule.
Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
