Skip to content

San Antonio homeowners

Sprinkler controller repair: timer not turning on or not running? What to check

Most "dead timer" calls turn out to be power, a rain sensor or the program. Check these before you replace the controller.

Fix your sprinklers
On this page

Check these before you replace the controller

The controller fails less often than it seems. Before replacing it, run through these checks. Most "dead timer" calls turn out to be power, a sensor, or a program.

Leer en español

Controllers differ. A plug-in controller runs on a low-voltage (24-volt) transformer: unplug it before touching any wire inside. If your controller is wired straight into house power (no plug), do not open it: it has 120-volt mains wiring inside, and any work there should be done by a licensed electrician. A licensed irrigator is not necessarily licensed for electrical work. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Sprinkler controller not turning on (blank display)

No power. Check the outlet with something else, check the transformer (the plug-in block. It should be warm and hum faintly), and check the fuse inside the cabinet if the model has one (the cabinet opens with a latch or a screw. The manual, or a search for the model name, shows where the fuse sits). A controller that lost power and came back may have reset to defaults. Re-enter the program. A battery (if fitted) only keeps the clock and program during an outage. It does not run the valves. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Sprinklers won't turn on with the timer (display works, no zone runs)

  1. Set the mode dial to “auto” or “run,” not “off” or “rain delay.”

  2. Flip the rain sensor bypass switch and try a zone.

  3. Run a zone manually from the controller and listen at the valve for a click.

  4. No click on any zone? On a plug-in controller, unplug it and check that the common wire is secure, then check the transformer output. On a hardwired controller, call a licensed electrician.

The common wire is the one wire shared by every valve, usually white. If you have a multimeter and a plug-in controller, about 24 to 28 volts AC across the common and a zone terminal while the zone runs is normal. On a hardwired controller, leave live testing to a licensed electrician. Stuck here? Call 210-697-9086.

Zones run at the wrong time or too often

Nearly always a program problem: two programs running, "odd/even" or interval watering set instead of custom days, a second start time left in, or the clock off after a power cut. Clear the extra programs and set one program with one watering day and a start time inside your water provider's allowed hours. How to program the controller walks through it step by step. Each start time runs the whole program again, so add a second one only on purpose, and shorten the run times to match, or the system uses double the water. Follow your provider's schedule (in San Antonio, the SAWS schedule). On smart controllers, an app schedule overriding the manual one is the common cause. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

One zone will not run from the controller

Swap that zone's wire with a working zone's terminal. If the dead zone now runs, the terminal (station) on the controller has failed. Many controllers have a spare station. So move the wire to it. If it is still dead, the fault is the wire or the valve. See our zone guide. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Repair or replace?

Replace when a station has failed and there is no spare, when the display or buttons are failing, or when the controller is more than about ten years old and you want weather-based scheduling. Typical replacements are a Hunter Pro-C or X2, a Rain Bird ESP-TM2, or a smart controller such as a Rachio. Apart from a new transformer or fuse, an old controller is usually not worth repairing. See smart controllers and drip. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Elsewhere in Texas

Set your timer to your own city's rules. Austin homes water once a week, on Wednesday or Thursday by address, before 10 a.m. or after 7 p.m. Dallas and Fort Worth water twice a week by address, never between 10 a.m. and 6 p.m. El Paso waters up to three days a week. When you replace a timer in Texas, the new one must have a rain or moisture sensor in most of the state. In Greater San Antonio, reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Sprinkler controller questions

Why won't my sprinklers turn on with the timer?

In order: the controller is off or in rain delay, the rain sensor is holding it off, the isolation valve is closed, or the common wire is loose. Run a zone by hand at the valve to separate a water problem from an electrical one.

Where can I get a sprinkler controller fixed?

SISCO fixes a dead transformer, fuse or program on site. A failed board or station is not worth repairing and the controller is replaced. Call 210-697-9086.

How do I reset a Hunter or Rain Bird controller?

On a plug-in Hunter Pro-C, the reset button is on the back of the front panel. Pressing it by itself restarts the controller, but pressing it while holding the Program button clears the memory (Hunter's instructions), so press it alone. On a plug-in Rain Bird ESP-TM2, the recessed reset button (press it with a paper clip) restarts it and keeps the schedules. On a hardwired controller, have a licensed electrician open it. The reset-to-defaults option in the special functions menu erases every program, so write the schedule down before you use it. After a reset, check the date and time, one program, one watering day and a start time inside your water provider's allowed hours.

Start here: All sprinkler guides.

Also useful: Smart controllers and drip. Sprinkler care by Texas region. Sprinkler zone not working.

Need help? Sprinkler repair in San Antonio.

When to call SISCO

A controller with no output, a failed station with no spare, wiring you cannot trace, or an upgrade to a smart controller: call 210-697-9086 or request sprinkler repair. Every controller we touch leaves on your water provider's current schedule.

Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.