Skip to content

San Antonio homeowners

How to find a sprinkler leak, a broken pipe, or the cause of low pressure

A soggy patch, a doubled water bill or a weak zone? Start with the meter test, then find the break or the real cause of low pressure.

Fix your sprinklers
On this page

Where sprinkler leaks hide

The symptoms arrive as a soggy patch that never dries, a water bill that doubled, a zone that runs weak while the others are fine, or water running when the system is off. This guide walks through finding the leak, tells you when to call a licensed irrigator, and explains the low-pressure causes that are not leaks at all. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Leer en español

Sprinkler system leaking when off: the meter test

  1. Turn the controller off and close every tap in the house.

  2. Lift the water meter lid at the curb with a screwdriver and watch the flow indicator.

  3. If it shows flow, close the irrigation isolation valve and look again.

  4. Flow stopped? The leak is in the irrigation system: call us at 210-697-9086. Still moving? Call a plumber.

The flow indicator is a small spinning dial or triangle on many meters. If your meter looks different, ask your water provider how to read it. A leak with the system off is on the pressure side: the main line, the backflow preventer, or a valve stuck open.

How to find a broken sprinkler pipe underground

Do not probe or dig to find a leak yourself. Texas law requires a call to 811 at least two business days ahead (not counting weekends and holidays) before digging, even in your own yard, and utility marks do not cover every buried line, such as private lines on your property. A probe or shovel can hit gas, electric and other lines.

  1. Run the suspect zone and walk it, looking for a wet or sunken spot.

  2. Watch the heads: the break is usually just before the first very weak head.

  3. Look for a stripe of greener grass along the pipe run.

  4. Mark the wet or sunken spot from the surface and stop there. Locating the break underground is a job for a licensed irrigator.

  5. If it leaks all the time, confirm a main line break with the meter test above.

Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Fixing a broken sprinkler pipe

Repairing a broken pipe means excavating around buried lines, and the right repair depends on the pipe type, depth and what else is buried nearby. Leave it to a licensed irrigator, who calls 811 and locates the pipe before any digging. Until it is repaired, turn off the zone at the controller (or the irrigation isolation valve if the leak runs with the system off) to limit water loss.

The main line (meter to valves) is under pressure all the time, so a bad joint there leaks continuously; if you cannot tell which pipe you are looking at, that one is worth a call: 210-697-9086.

Low pressure that is not a leak

Weak sprinklers do not always mean a leak. Check in this order.

Every zone weak: the isolation valve or the backflow preventer's ball valves are partly closed, the backflow preventer is clogged, or the home's supply pressure dropped. A pressure gauge screwed onto an outdoor faucet (a hardware-store item, safe to use) shows the static pressure, the pressure with nothing running. Spray heads want about 30 psi and rotors about 45 psi while running, and the backflow preventer, valve and pipe each take some off. As a rough guide, 50 to 70 psi static is comfortable, and under 40 will struggle on rotor zones. A system that has always run weak was probably designed with too many heads per zone. The fix is splitting zones.

One zone weak: a valve flow control screwed down, a diaphragm partly fouled, a lateral break, or too many heads on the zone (common after someone added heads).

A few heads weak: clogged nozzles or filters, or a head at the far end of a long run.

If pressure cannot be raised: rotary nozzles (Hunter MP Rotator, roughly 25 to 55 psi depending on model. Rain Bird R-VAN, 30 to 55 psi) use less flow per head than spray nozzles, so an overloaded zone regains pressure. They apply water more slowly: Hunter says the zone should run two to three times longer than a spray zone but still uses about 30 percent less water. They are the usual answer for low water pressure, but they do not fix a supply that is truly under 30 psi.

Weak only at certain times: supply pressure can dip when many neighbors water at once. Check the static pressure at different times of day, and if it drops, ask your water provider about it.

Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

A sprinkler leak and a high SAWS water bill

An irrigation leak can waste thousands of gallons a month without visible flooding, most of all a main line leak feeding into clay soil. If your SAWS bill jumped, do the meter test above the same day. A valve stuck open is the other common cause. SAWS will consider a leak adjustment for a main line break or non-working nozzles if you ask within 60 days of the repair with a receipt or a description of the work. See SAWS leak adjustments. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Elsewhere in Texas

Leaks cost you in other Texas cities too. Dallas, Fort Worth and New Braunfels treat runoff and unrepaired leaks as water waste. El Paso requires leaks to be fixed within five working days. In the Hill Country and much of Central Texas, pipe runs shallow over rock, so edgers and shovels hit it. In Greater San Antonio, reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Sprinkler leak questions

How do I find a leak in my sprinkler system?

Turn the controller off and check the water meter. If it is still turning, shut the irrigation isolation valve and check again. A meter that stops means the leak is in the irrigation system. Then run each zone and look for weak heads, wet or sunken spots, and unusually green strips along the pipe run.

Why is my sprinkler system leaking when it is off?

A sprinkler system that leaks with the controller off has one of three faults: a valve stuck open from debris under the diaphragm, a leaking backflow preventer, or a break in the main line, which is under pressure all the time. Shut the isolation valve to stop it, then find which of the three it is.

Why does one sprinkler zone have low pressure?

One weak zone usually has a lateral line break, a valve flow control turned down, a fouled diaphragm, or too many heads on the zone. If every zone is weak, the problem is upstream at the backflow preventer or the supply.

Can I fix a broken sprinkler pipe myself?

A broken pipe, a main line break, a leak you cannot locate, or anything near the backflow preventer is a job for a licensed irrigator, because digging near buried lines is hazardous and a bad joint on the main line leaks continuously. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.

Start here: All sprinkler guides.

Also useful: Sprinkler head problems. Sprinkler zone not working. Sprinkler valve problems.

Need help? Sprinkler repair in San Antonio.

When to call SISCO

A leak you cannot find, a main line break, a backflow preventer leak, or low pressure on every zone: call 210-697-9086 or request sprinkler repair. We locate the leak, repair it and pressure-test the zone, and describe the repair on the invoice, which is what a SAWS leak adjustment request asks for.

Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.