Homeowners
Stamped irrigation plans, built for SAWS review
Stamped by licensed irrigator LI 31500, submitted to SAWS, every comment handled. Plans in as little as 3 days.
Fix your sprinklersOn this page
Stamped irrigation plans for the SAWS service area
Since January 1, 2025, every new irrigation system in the San Antonio Water System (SAWS) service area needs a plan stamped by a licensed irrigator, submitted to SAWS and approved before installation. SAWS conducts operational inspections of newly constructed irrigation systems beginning January 1, 2026, and a new location needs an approved plan on file and a passed inspection to remove holds on water accounts. SISCO prepares the plan, seals it, submits it, answers SAWS comments and revises the drawing. Approval remains with SAWS; the comments and revisions are ours to handle. One contact from lot to approval. Texas Commission on Environmental Quality (TCEQ) licensed irrigator LI 31500.
Send us one lot. Call 210-697-9086 or email service@siscoirrigation.com with a lot and floor plan and we'll confirm the scope.
Who we design irrigation plans for
Production home builders who need a stamped plan for every lot and can't have SAWS comments stall a close. We work with your construction lead and your irrigation trade. Your contractor stays on the install.
Irrigation contractors and landscapers who install but don't design, or who are backed up on drawings. We draw and seal to your layout, and you keep the customer.
Landscape architects and designers who need the irrigation sheet sealed by a licensed irrigator for a permit set.
Pool builders and landscapers: see irrigation plans for pool builders and landscapers.
Commercial projects: case by case. Inside San Antonio city limits, commercial plans go to City of San Antonio Development Services first and then to SAWS. Call 210-697-9086 to talk it through.
What SAWS requires, and why plans come back
SAWS reviews every plan against a TCEQ checklist, with a goal of five business days, and returns it with a list of what fell short. Most returns come down to the same handful of items.
The stamp: the plan must carry the seal of a TCEQ-licensed irrigator. Unsealed drawings, or drawings sealed by someone without an irrigator license, come back.
Head arcs: arcs must be drawn so coverage can be judged.
Pipe sizes: mainline and lateral sizes on every section, not only in a legend.
Scale: both a numerical and a graphical scale.
Pressure regulation: the method stated on the plan and the regulating parts in the legend. This is the most common omission. SAWS says a plan without it may be rejected.
One precipitation rate per zone: within 15 percent. Spray heads with rotors, spray with bubblers, or drip with bubblers on the same zone send a plan back.
Hydrozoning: trees, shrubs and turf on separate zones.
Property details: the meter number or property address, plus owner or builder contact details.
A legible PDF: low-resolution scans come back.
Size: home plans must cover under 10,000 square feet of irrigated area.
A plan built to this checklist the first time avoids the resubmission loop. That is what we deliver. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Residential irrigation plans in San Antonio
A new home system on SAWS water needs a stamped plan that SAWS approves before the work starts. Since 2026 it also needs a passed SAWS inspection at the end. SAWS treats a home plan as one with under 10,000 square feet of watered area. Inside the city, the permit comes from Development Services.
We draw the plan for your lot, seal it under license LI 31500 and show what SAWS looks for.
Tell us what the city or your reviewer asks for. We prepare the plan to meet it.
Commercial irrigation plans in San Antonio
Shops, offices, apartments and shared areas need a stamped plan too. Past 10,000 square feet of watered area, SAWS gives the plan a larger review. Large sites also file a yearly sprinkler checkup with SAWS by May 1. That covers sites of 5 acres or more, or ones that use over 1 million gallons a year on the landscape.
Send us the site plan and the landscape plan. We size the zones, pipe and meter for the site and seal the plan.
Tell us what the city or your reviewer asks for. We prepare the plan to meet it. See irrigation plans for commercial sites, or ask for a plan quote.
For the watering rules a finished system must follow, see SAWS watering days and rules.
Irrigation design services: what SISCO delivers
The irrigation design: zones, heads, drip planning for beds, pipe sizing, pressure regulation and controller, drawn to the lot and the landscape plan. A standard system is up to 8 zones.
The licensed seal: LI 31500 and the TCEQ statement.
Submission to SAWS: through its online form, with the meter number or address and your contact details filled in. Commercial plans inside San Antonio city limits go to City of San Antonio Development Services first, and the stamped copy then goes to SAWS.
Comment responses: when SAWS returns the plan, we revise and resubmit. You see the comment and the fix; you don't have to answer it.
The homeowner packet SAWS inspectors look for at the controller: seasonal schedule, as-built plan, maintenance schedule, controller manual and TCEQ statement.
Inspection support: we design around SAWS's published inspection list, tell the installer what the inspector checks, and can be on site for the SAWS operational inspection. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Help with the new-landscape variance request, which is a separate request to SAWS from the plan. SAWS can allow up to five weeks of weekday watering from landscape installation, and asks for drought-tolerant turf on 4 inches of soil, a working rain sensor, a current backflow inspection and the permit number. SAWS decides the request.
Designed around SAWS's 2026 inspection list
SAWS publishes why installed systems fail inspection. Our plans are drawn with that list in hand, and our inspection notes tell the installer what the inspector checks: heads at least 4 inches from pavement and none across the property line. Head spacing within 10 percent of the design. No overspray onto fences or hard surfaces. Flow control set so heads don't mist. Check-valve spray bodies at the low point of each zone so zones don't drain onto the sidewalk. A working rain sensor. At least 4 inches of prepared topsoil, free of rocks and construction debris. And the paperwork packet at the controller. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
How it works
Send the job: lot and floor plan, options, site notes and irrigation scope, by email.
We draw, review and seal the plan, in as little as 3 days.
We submit to SAWS and handle every comment.
You install to the approved plan with our inspection notes and controller packet.
Approval and a passed inspection release the hold on the water account. The landscape variance is a separate request to SAWS.
Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Start with one community
Bring us one real job. Send a lot and floor plan. We confirm the scope with your team and show you the handoff. For builders, a pilot of 25 plans over 30 days shows whether the handoff fits your schedule. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Why SISCO
Licensed irrigator on staff, LI 31500. You can check any license on the TCEQ website. We have 40 years in the San Antonio metro in irrigation and landscapes.
We also repair systems across Greater San Antonio. So we know where designs fail in the ground, not just on paper. See sprinkler repair in San Antonio.
We keep the SAWS watering rules and plan rules current on our water provider pages, which is how we stay ahead of rule changes like the 2025 plan mandate and the 2026 inspections. Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
Across Texas
TCEQ license LI 31500 is valid across Texas, and TCEQ requires a licensed irrigator's sealed design for every irrigation system installed for pay in the state, whoever the water provider is. Outside San Antonio, we submit the plan to whatever review the city permit office or the municipal water authority requires, and handle comments and revisions the same way. Plan review rules differ by water provider and city. See find your water provider for Boerne, Schertz, New Braunfels and the rest of Greater San Antonio.
Send us one lot
Call 210-697-9086 or email service@siscoirrigation.com with the lot and floor plan.
Irrigation plan questions
Do I need an irrigation plan for a new sprinkler system in San Antonio?
Yes. Every irrigation system built in the SAWS service area after January 1, 2025, home or commercial, needs a plan stamped by a TCEQ-licensed irrigator, submitted to SAWS and approved before the system is operated. Since January 1, 2026, the installed system must also pass a SAWS operational inspection. This is separate from the City of San Antonio irrigation permit.
Who can stamp an irrigation plan in Texas?
SAWS's review checklist calls for the seal of a Licensed Irrigator holding a TCEQ license, and TCEQ requires a sealed plan for every irrigation system installed for pay in Texas. SISCO's license is LI 31500, which you can check on the TCEQ website.
How long does SAWS take to review an irrigation plan?
SAWS's stated goal is five business days, and a plan with no deficiencies may be approved sooner. A plan with deficiencies comes back by email with the checklist items that fell short, and the total time depends on how quickly the revisions are made and returned, which is why getting it right the first time matters most.
Why did SAWS reject my irrigation plan?
The usual reasons are a missing statement of pressure regulation, zones that mix heads with different precipitation rates, missing arcs or pipe sizes, no scale, a missing meter number or contact details, or a low-resolution file. SISCO reviews plans against SAWS's checklist before submission and handles the resubmission if a comment comes back.
More irrigation plan questions
What happens if a new system is installed without an approved plan? SAWS's 2026 program says a new location must have an approved plan on file and pass the operational inspection before its holds are removed. That delays the new-landscape watering variance and, at resale, the account transfer. For a builder, it means a lot that cannot close cleanly and a homeowner who cannot water a new lawn.
What does the SAWS irrigation inspection check? That the system matches the approved plan and passes SAWS's published list: heads at least 4 inches from pavement and inside the property line, zone pressure within 10 percent of the design pressure, matched precipitation rates, head-to-head coverage, no overspray, check valves at zone low points, a working rain sensor, at least 4 inches of prepared topsoil, and the paperwork packet at the controller.
Does my landscaper need to be a licensed irrigator in Texas? To design, install, alter or repair an irrigation system for pay, yes: Texas requires a TCEQ Licensed Irrigator, or an Irrigation Technician working under one. Homeowners may work on their own systems. You can look up any license on the TCEQ website.
Can SISCO design the system if my own contractor installs it? Yes. That is the normal arrangement for builders: we draw, seal and submit, and your irrigation contractor installs to the approved plan with our inspection notes. We also design for irrigation contractors who don't have a licensed irrigator on staff.
How much does a stamped irrigation plan cost? It depends on the lot, the number of zones and whether the project is home or commercial. Send us the lot and floor plan and we'll confirm the scope and quote it.
Reach out to the irrigation experts at SISCO Irrigation at 210-697-9086.
We draw plans for every city in San Antonio and the Hill Country.
